Quantcast
Channel: Motorcycles Repair Manual Download and Reviews » Search Results » how to remove 2006 harley sportster swingarm bolt removal
Viewing all articles
Browse latest Browse all 10

GL1800 Goldwing Trike Conversion Kit Installation Instructions

0
0

download
Disassembly of motorcycle: 1. Place the motorcycle on the center stand or lift. 2. Set the shock preload to zero. 3. Remove the four m8 x 1.25 SHCS from the passenger handles and remove seat. 4. Remove the rear side covers. 5. Disconnect negative battery terminal. 6. Remove the four m8 x 1.25 SHCS and the passenger floorboards. 7. Remove the six m5 x 0.80 BHCS and the foot rest under cover. 8. Remove the six m5 x .80 BHCS and the swing arm pivot bolt covers. 9. Remove the four m8 x 1.25 flange bolts on the rear crash guards. Remove and discard the rear crash guards and bolts. 10. Remove the four #2 Phillips head screws from the inside of the trunk to remove the trim pieces on the sides. 11. Remove the two #2 Phillips head screws in the rear trim molding and remove molding. 12. Remove the seven #2 Phillips head screws from the lower trunk cover. Remove the lower trunk cover. 13. Remove the five #2 Phillips head screws from the trunk opener cover. Remove the trunk opener cover. 14. Disconnect the left and right saddlebag release cables. 15. Remove the five m6 x 1.0 BHCS in the rear fender panel. Remove and discard the rear fender panel and cap screws. 16. Disconnect the trunk wiring. 17. Remove the four m6 x 1.0 flange screws. Remove the trunk from the saddlebag / trunk stay. 7 18. 2005 and older 2005 and older 2005 and older 2005 and older ABS equipped motorcycles: ABS equipped motorcycles: ABS equipped motorcycles: ABS equipped motorcycles: Remove rubber bungee from ABS Control Unit, and save for reinstallation. 19. Remove the two side cover grommets from each saddlebag. ( 4 grommets total ) 20. Remove the left and right hand saddlebag latches, strikers, and release cables for core parts return. Refer to Honda service manual. 21. Remove the left and right saddlebag taillights and sub- harnesses for core parts return . Refer to Honda service manual. 22. Remove the four m6 x 1.0 flange bolts from each saddlebag. Remove and discard the saddlebags. 23. Remove the six m6 x 1.0 flange bolts from the exhaust tips. Slide the tip off the muffler body. Save tips and bolts for reinstallation. 24. Loosen the four m8 x 1.25 SHCS on the muffler clamps. Remove the two m8 x 1.25 flange bolts. Remove and discard the mufflers and muffler gaskets. 25. Remove the four m6 x 1.0 BHCS, two rubber washers, and front fender A. 26. Remove the four m5 x .80 BHCS and chrome front fender covers. 27. 2006 & UP. 2006 & UP. 2006 & UP. 2006 & UP. Remove the Remove the Remove the Remove the two m6 x two m6 x two m6 x two m6 x 1.0 flange bolts on 1.0 flange bolts on 1.0 flange bolts on 1.0 flange bolts on rear of saddlebag/trunk stay. rear of saddlebag/trunk stay. rear of saddlebag/trunk stay. rear of saddlebag/trunk stay. 28. Unplug connector and remove amp and save for Unplug connector and remove amp and save for Unplug connector and remove amp and save for Unplug connector and remove amp and save for reinstallation. reinstallation. reinstallation. reinstallation. 29. Cut lower saddlebag supports off the saddlebag/trunk stay, where the round tubing meets the square, and cut the gusset flush, removing any burrs. See Figure 1. 30. Remove trunk stay for later use. 31. Remove the two m5 x .80 nuts on the license plate light. Remove and discard the license plate ligh

Incoming search terms:


Viewing all articles
Browse latest Browse all 10

Latest Images

Trending Articles





Latest Images